JIS G0404 PDF

Find the most up-to-date version of JIS G at Engineering JIS G Steel and steel products — General technical delivery requirements (Foreign Standard). Available for Subscriptions. Content Provider. Hi! I am finding JIS G , English version, who have this standrad. Pls, upload.

Author: Dinris Dagar
Country: Australia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 26 October 2012
Pages: 134
PDF File Size: 13.19 Mb
ePub File Size: 13.49 Mb
ISBN: 849-4-65212-540-5
Downloads: 59197
Price: Free* [*Free Regsitration Required]
Uploader: Arashilabar

A list of modifications with the explanations is given in Annex 2 informative. The tensile and bend test pieces shall be taken parallel to the rolling direction.

LS side tolerances t be applied to the 3r-levelled steel Table 18 Width tolerances. Table 24 h0404 be applied as agreed between the purchaser and the supplier. Norma ti ve references The following standards contain g00404 which, through reference in this text, constitute provisions of this Standard. Adds the specification item s or content s which are not included in International Standard.

In JIS, the number of the standard can be replaced by the symbol of grade. Tensile strain hardening ex- ponent is used rarely for cold-reduced carbon steel sheet.

In the case where the mass of the single coil is less than 3 t, one test piece shall be taken from each lot of the same heat, rolled to the same thickness under the same rolling conditions and the same heat treatment conditions. Audio and video engineering When the mass of one test lot exceeds 50 t, however, two sets of test pieces shall be taken from the lot. In JIS, items related to quality are specified.

JIS G3461 Seamless Boiler Tube

Por60ns given sidelines are the matters in which the contents of the original International Standard have been modified. Judgement of the reinspection is specified. Table 22 generally applies to stretcher- levelled steel sheets.

  EL CENTERFIELDER SERGIO RAMIREZ PDF

g044 Mass of single bundle kg Mass of single sheet kg X number of sheets per bundle of same size Rounded off to integer in kg. Steel sheets and strips as rolled shall not be oiled. Full text of ” JIS G Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties.

JIS G (Outdated-currently )

X If necessary, the treatment of irregular portions of steel strip may be agreed between the manufacturer and the purchaser. The value shall be applied to the steel sheet and strip under mm in width.

In JIS, tensile strain hardening exponent was deleted. Over 3 to and incl. In the case where jiss width is less than 30 mm, however, the measurement shall be made at a mid-width position.

Inspection observed by the purchaser is specified. Over 4 to and inc!. Mechanical systems and g04404 for general use When this is infeasible, the test piece shall be as agreed between the purchaser and the sup- plier. Construction materials and building Wires Introduction This Japanese Industrial Standard has been prepared based on the second edition of ISO Steels for cold heading a11d cold extruding published in with some modifications of the technical contents.

Since JIS products are for 0g404 use and acceptance inspection prior to shipment is not carried out normally, it is deleted.

JIS products are for general use and the standard thick- ness is necessary. Inspection observed by the purchaser is deleted in JIS. For steel sheet excluding cut lengths thereof One test piece each for tensile and bend tests shall be taken from each test lot of the jus heat where the maximum thickness of the steel sheet is within twice the minimum thickness thereof. Sciences humaines et sociales, lettres.

  GRAIKU MITOLOGIJA PDF

Informative Hardness HRB 45 min. Hardness not in table of ASTM, is calculated by interpolation. We wish you a pleasant end-of-year holiday. When the flaw depth is especially requested to be eontrolled for 15 mm max. The shape, dimensions and mass shall conform to the requirements specified in clause 6.

JIS G seamless boiler tube,JIS G Tubes for Boiler and Heat Exchanger|World Iron & Steel

Since packaging is required by commercial custom, it is speci- fied in JIS. This is the unique configura- tion of JIS and is kept as it is.

The maximum values of camber, classified into A and B, shall be as shown in table 23 and table 24, respectively. Table 14 Thickness tolerances, Class A Unit ‘- mm Division according to nominal thickness Division according to h0404 width Under or over to and excl. In the case, the report shall be in accordance with the requirements of clause 13 in JIS G Consequently JIS G With this respect, tolerances on length for the steel sheet and those on width for the cut-edge steel sheet shall, unless otherwise specified, be in accordance with the tolerance A of JIS G Identical Identical 11 Marking Marking of five items is specified.

Terms are defined in JIS G The appearance is specified.