Coefficient of Linear Thermal Expansion by TMA or Dilatometer ASTM E, ASTM D, ISO Scope: Linear Thermal Expansion is used to determine . This standard is issued under the fixed designation E; the 1 This test method is under the jurisdiction of ASTM Committee E37 on Thermal. ASTM E Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis_机械/仪表_工程科技_专业资料。Designation: E
|Published (Last):||6 December 2008|
|PDF File Size:||11.46 Mb|
|ePub File Size:||14.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
Inspection Validating the specifications, value and safety of your raw materials, products and assets. In the case of dispute, only the manual procedures described in this test method are to be considered valid.
Coefficient of Linear Thermal Expansion ASTM E, ASTM D, ISO
Related information can be found in Refs. Summary of Test Method 4. NOTE 5—Direct readout of zero position and specimen length using the analyzer sensing element, where available, with a sufficient range astj been found to be an accurate means of length determination. A graph is produced. A number in parentheses indicates the year of last reapproval.
This aetm is subject to revision at any time by the responsible technical committee and must be reviewed every? Precision and Bias 6 Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Link aztm Active This link will always route to the current Active version of the standard. This test method uses a smaller specimen and substantially different apparatus than Test Methods E and D An abrupt change in slope of the expansion curve indicates a transition of the material from one state to another.
Due to copyright restrictions, we are not able to provide copies of standards. Note 1 Users of this test method are expressly advised that all such instruments or techniques may not be equivalent. Active view current version of standard. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
The specimen must be flat on both ends. This standard does not purport to address all of the safety problems, if any, atsm with its use. The last approved version of this historical standard is referenced on www. The measured DL for the specimen should normally be corrected for this instrument baseline, especially for low expansion specimens. The temperature range may be extended depending upon the instrumentation and calibration materials used.
Linear Thermal Expansion is used to determine the rate at which a material expands as a function of temperature. Coefficient of Linear Thermal Expansion Video Learn more about linear thermal expansion in this video.
Retest of a specimen may be used only as reference and shall not be treated as an independent test of a sstm specimen. Assurance Enabling you to identify and mitigate e31 intrinsic risk in your operations, supply chains and business processes. E — 06 ambient temperature, accompanying a unit asmt in temperature identi? Active view current version of standard.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The am shall not be calculated from a temperature range in which a transition point is noted.
Coefficient of Linear Thermal Expansion ASTM E831, ASTM D696, ISO 11359
NOTE 7—For best results, specimen temperature gradients should be small. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This test can be used for design purposes and to determine if failure by thermal stress may occur. Send us a request Need help astk have a question?
ASTM E – THERMAL EXPANSION BY TMA
Specimens that do not meet these requirements may result in increased imprecision. The specimen is placed sstm the Dilatometer at room temperature, and the height gauge is positioned and zeroed. The specimen is heated at a specified rate, often ten degrees a minute, over the desired temperature range.
Validating the specifications, value and safety of your raw materials, products and assets. The test method may be used at lower or negative expansion levels with decreased accuracy and precision see Section.
The height is measured by the probe. E — 06 is adequate. The effects of specimen temperature gradients may be compensated for by correction found through the use of suitable reference materials whose size and thermal conductivity are close to that of the test specimen.
NOTE 1—Users of this test method are expressly advised that all such instruments or techniques may not asfm equivalent. Alternatively, a dilatometer can be used. Need help or have a question? Work Item s – proposed revisions of this standard. The observed expansion must be corrected for the difference in expansion between the specimen holder and probe obtained from a blank run in which no sample or a specimen of the material of construction of the probe is run.
Standard Test Method f The coefficient of linear thermal expansion can be calculated from these recorded data.
Work Item s – proposed revisions of this standard. Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.