ASTM A480 PDF

ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.

Author: Barn Tojasho
Country: China
Language: English (Spanish)
Genre: Education
Published (Last): 13 June 2015
Pages: 148
PDF File Size: 14.91 Mb
ePub File Size: 2.84 Mb
ISBN: 450-5-87009-337-9
Downloads: 47559
Price: Free* [*Free Regsitration Required]
Uploader: Melar

ASTM A Specification | Penn Stainless Products

Within the text, the SI units are shown in brackets, except 4a80 when AM is specified, Annex A3 shall apply for the dimensional tolerances and not the bracketed SI values in Annex A2. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product speci? Thickness tolerances given in mm unless otherwise indicated.

Special tests like intergranular corrosion test, permeability test, Charpy impact testing zstm tests for detrimental intermetallic phases in wrought duplex stainless steels shall be also be performed when required. Test data from a minimum of three test lots, as de?

Bright Annealed Finish—See Note 4. In the case of heavier plates of types other than L, LN, Cb, Cb, Cb, L, LN, Ti, L,S, and S, the applicability of this test shall be a matter for negotiation between the seller and the purchaser. Such requirements may include, but are not limited to, the following: In the case of polished? For narrow strip, the following widths can be tested: If the hardness difference between the two ends of the coil exceeds 5 HRB, or equivalent, or if the material is temper rolled, tensile properties must be determined on both coil ends.

  DVX100A MANUAL PDF

However, it is not necessary to actually run the test unless it is speci?

ASTM A480 Specification

NOTE 2—If the longer dimension is under 36 in. For thicknesses under 0. It is neither practical nor necessary to specify limits for unspeci? Users of this standard are expressly advised that determination atm the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Requirements for A are given in Annex A2.

Appearance z480 vary depending upon the starting? This is a dull, nonre? The steel shall be made by one of the following processes: C Quenched in water or rapidly cooled by other means.

Finish for Sheet The applicable levels shall be as speci? Average surface roughness Ra may generally be up to 25 micro-inches.

ASTM A Plate Thickness & Flatness Tolerances – Rolled Alloys, Inc.

Current edition approved Dec. The inside of the coil shall also be marked or shall have a tag or label attached and marked with the information of Approved April 1, The presence of an unspeci? All widths and lengths 1 16 18 1 16 18 Over mm 1.

Bright Annealed Finish —A smooth, bright, re? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The material shall be accepted if the results of retests on retreated material are within the speci? TR Finish—See Note 4.

  LEMOINE SOLFEGE 1A PDF

For plates up to 10 in. B For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown.

The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; a4800 example, by waiving a test requirement or by making a test requirement less stringent. This is a general purpose? NOTE 1—A typical ordering description is as follows: Refer to Section Edges for Cold-Rolled Strip The values stated in each system are not exact equivalents; therefore, each system must be used independently asfm the other.

Width and length tolerances for abrasive cut plates over mm thick are not included in the table; consult producer.

For the purposes of this speci? An iron free astmm wheel shall be used for such grinding and shall be operated at a speed ample to ensure that defective areas are cleanly cut out.

NOTE 3—For plates with speci? It is produced by buffing a? B Recommended cleanup allowance which, unless otherwise speci? Approved November 15, Repair of Plate by Welding